What to do Huawei Honor 10 Lite freezes on the splash screen and does not turn on, but reboots endlessly? We will help you sort this matter out. In fact, you have an Android brick in your hands, but this can be solved.
Android constantly reboots or gets stuck on the splash screen
Look at the most common variants of the problem:
Do not try to disassemble the phone yourself and identify the cause of the breakdown; if you break the seals, you will lose the warranty and risk not being able to put it back together.
How to restore a brick on Android? The best way out of the situation is to flash the device to the factory firmware; below we tell you how to do this
What should I do if Honor 5A freezes on the splash screen and does not turn on, but reboots endlessly? We will help you sort this matter out. In fact, you have an Android brick in your hands, but this can be solved.
Why Android freezes on the logo when turned on
To flash the firmware via ZYKUFlasher, read the instructions written on the same site (here). I don’t see any point in rewriting this into my article, but if you need my help, please leave feedback. I would like to ask you to leave your feedback on this method of restoring an Android smartphone, I hope it won’t take much time.
What to do Huawei Honor 9 freezes on the splash screen and does not turn on, but reboots endlessly? We will help you sort this matter out. To put it bluntly, you actually have a backlit “brick” in your hands.
The phone does not turn on beyond the splash screen
Do not try to disassemble the phone and independently determine the cause of the breakdown, since in this case you may lose the warranty, and without certain skills you can only make things worse and it will stop turning on altogether, and this is exactly what we don’t need.
For ZYKUFlasher, we use the instructions written on the same site (here), fill in the necessary fields in the program and click Start Flash. Actually, there is nothing complicated there, and for those who are afraid, I can help in the comments if necessary. I would like to ask you to leave feedback, maybe someone will suggest new ways that will be of interest to our readers.
Now let’s figure out why your Android phone doesn’t load beyond the logo (it doesn’t turn on after the manufacturer’s or robot’s splash screen). Further in the text: first about the reasons and then a deciphering of what to do in this or that case.
This article is suitable for all brands that produce Android phones 13/12/11/10: Samsung, Xiaomi, Redmi, Poco, Huawei, Honor, Lenovo, Tecno, Realme, etc. We are not responsible for your actions .
You can ask your question to a specialist at the end of the article.
If we divide all the reasons why your Android phone hangs on the logo screensaver and does not load further, then this will be
Causes of failure and why it turns on but does not boot
⭐️⭐️⭐️⭐️⭐️ If Android does not load on your phone or tablet when you turn it on, or your Android smartphone starts but does not go beyond the logo splash screen, then the reasons for this may be the following:
Read How to check Android for errors
Before you try to troubleshoot Android, you need to understand why the system won’t boot.
Don’t know how to solve a problem with your gadget and need expert advice? Alexey, a smartphone and tablet repairman at the service center, answers your questions. Write to me »
Restoring functionality
If the phone shows that it is charging, then the causes of the problem should be looked for in the operation of Launcher Android. If your device vibrates or its screen flickers, there is a possibility that the screen is damaged.
If you determine that the problem is software in nature (for example, the problem arose after a firmware update), then a simple reboot will not help. You need to reset the system via Recovery Mode or reflash the device. Let’s see what to do:
Resetting the settings will delete the user’s personal data and settings. If this method does not help, perform a flashing. To do this, upload the file with the appropriate firmware to the root of the memory card, insert the drive into the phone and select “Install zip from sdcard” in Recovery Mode.
You can deal with a software glitch yourself, but how can you fix hardware problems? The most reasonable option is to contact a service center for diagnostics and repairs.
Even if the problem can be solved without financial investment, by simply flashing it, users have an important question – how to save the data stored in the phone’s memory. There are no problems with the memory card: you just need to remove it from the device. But how to save data from the internal drive? For example, pull out contacts.
If you backed up your system or at least turned on Google synchronization, then getting your contacts will be very easy. All you have to do is go to the Contacts app on Google to see the full list of synced contacts. If you want to transfer them to another device, all you need to do is add a Google account to it.
To make it as easy to get other information, you need to periodically backup Android. Then if the phone reboots and resetting does not help, you can safely reflash it without worrying about the safety of the information.
You can, for example, install a custom Recovery and copy data to a memory card using the “Backup” function.
Mobile and computer equipment repair engineer in a specialized service center, Moscow. Continuous work experience since 2010. Have questions? Ask in the comments to the article. I try to respond to your email as quickly as possible. Each case is individual and therefore it is very important that you describe your problem as best as possible and what model of device you have.
Honor phone turns on and off
Question asked 3 years ago
Answers to the question
Completely disassemble the device, clean it from traces of moisture, dry it, blow it with a compressor (if possible)
You have a short circuit on the board. Take it to the SC. It is necessary to clean, remove oxides and restore damaged elements on the board.
It is necessary to completely disassemble the phone, clean the oxides, and diagnose the boards at a service center. Repair from 1000 rubles.
Most likely there is a short in the activation button circuit. But if water gets inside the phone, you need to completely disassemble it and clean the board in an ultrasonic bath. Then solder the damaged areas.
Good afternoon. It is necessary to disassemble the device and clean it from spills. There is probably a short circuit somewhere on the board – we need to look for it and fix it. The problem could also be in the firmware, battery, or button cable. Contact the service center.
Good afternoon. First of all, this device must be cleaned using an ultrasonic bath. Next you need to check the battery and charging and charging controllers. But cleaning often enough will help.
Disassemble and look for oxides. Try flashing
Good afternoon, the board will need ultrasonic cleaning, and most likely the power button will need to be replaced.
Good afternoon. It is necessary to disassemble the device and clean it from spills. There is probably a short circuit somewhere on the board – we need to look for it and fix it. The problem could also be in the firmware, battery, or button cable. Contact the service center.
Good afternoon. First of all, this device must be cleaned using an ultrasonic bath. Next you need to check the battery and charging and charging controllers. But cleaning often enough will help.
Good afternoon! First of all, it is better to clean it in an ultrasonic bath, then recheck the activation button and cable, then check the board for a short circuit, or the charging controller has failed
Very carefully, if possible under a microscope, or at least under a magnifying glass, inspect the system board and all connectors and cables for oxides and corrosion. If necessary and possible, restore (replace) faulty components and parts. Recheck the battery.
Disassemble, when it starts to turn on, turn off the activation button and if everything is ok, then the problem is in the button, look and clean
Good afternoon. It is better to contact a service center. Most likely there is a short circuit on the board, a problem with the memory, a problem with the charging button.
Good afternoon. Alternatively, the activation button is stuck. But this is not all that could cause the phone to fail. It is better to completely disassemble the phone and thoroughly clean the circuit board and activation button cable.
It is necessary to clean all boards and elements from oxides in an ultrasonic bath and perform diagnostics with measuring instruments in a service center.
The problem can be either in the firmware or in the battery, first you need to reflash it by entering the firmware mode by closing 2 contacts to contact on average 1000 rubles, if you need to replace the battery 1500 rubles
Resetting to default configs will save you
Memory failure, only replacing it will solve your situation.
It looks like the buttons are stuck or moisture has entered. This is the launch of test mode on Chinese smartphones.
First of all, you need to prevent moisture from getting inside the phone. To do this, you need to disassemble it and carefully examine the board under a microscope. If you still find traces of exposure to moisture, you need to clean it in an ultrasonic bath and solder the contacts that have become oxidized.
Either the buttons are jammed or there is a short circuit.
This is the engineering menu. Apparently the button block was flooded. It is necessary to clean or replace the unit with cable 1000-2500
Moisture in the button area, broken buttons, software glitch, diagnostics will be required.
Most likely this is a result of moisture or shock. There is also a possibility that it is a software issue. But in any case, it is better to contact a service center to have the board examined first.
This is a processor blade, it needs to be rolled
Good afternoon. It is better to contact a service center. There may be a short circuit on the board, a problem with the memory, or a problem with the charging button.
First try to turn off the phone and go into Recovery. To do this, with the phone turned off, you need to simultaneously hold down the activation button and the volume up rocker. If possible, reset the settings (wipe data/factory reset). Please note that after resetting all data will be deleted! In addition, you need to write down the details of the Google account with which the phone was synchronized before the reset! If resetting does not help, then you need to open the phone and check the button cable. It’s quite likely that liquid got inside the phone and there are oxides on the cable or connector.
Button or sensors. Take it to the SC
The battery, charging connector, charging controller, charging circuits, system board, activation button, processor, memory chip, software failure are probably faulty. Try to do a hard reset in recowery. If it doesn’t help, then diagnostics are needed at a service center.
Good afternoon! You need to double-check the activation button cable, probably the problem lies there. If there are no defects, then there may be a problem with the light sensor. The problem could also be in the software, resetting the settings should help in such a situation
Of course it was. The problem may be in the firmware, battery, button, board. Diagnostics required.
The problem may be in the firmware, memory chip, controller or charging circuits, or battery. If there was a problem with the button, then the phone would give the option to reboot or shutdown without additional inscriptions.
Looks like an activation button. You should start the diagnosis by throwing up the cable with the button
Good afternoon. First, you need to disassemble the device and double-check for moisture and contamination. If you exclude these points, you will need firmware for the device link
Good afternoon.
To make sure whether your version is correct, you need to disassemble the phone and get to the buttons, accordingly clean the button cable and recheck their functionality. Also clean the phone case. If after these procedures the problem does not go away, then most likely the problem is in the main board. Diagnostics at the SC is required. Good luck!)
Try flashing here. link. If it doesn’t help, then diagnostics are needed at a service center.
There is a problem with the board in the bluetooth module
Try to completely disable the power saving mode in add-ons and test the device with a headset.
Try changing the configs of the Bluetooth application to run in the background and power saving functions.
Reset the software, install the latest system updates, if it doesn’t help, then contact the warranty
If malfunctions occur with other Bluetooth devices, then the problem is in the hardware: coaxial cord, Bluetooth module.
Most likely the battery, system board, charging circuits, processor, memory chip, software failure are faulty. Try flashing your phone. If the problem remains, then diagnostics at a service center is necessary.
Probably a problem with the software. Try flashing:
link
If this doesn’t work, contact the service center.
Good afternoon. There may be a problem with the software – a reset and flashing will help. Either there is a problem with the memory – it needs to be replaced, or mat. full payment.
You should always try to flash it first to avoid a software failure. Next, open the phone and test the charging circuit. The internal memory chip has probably failed.
The problem can be either software or hardware. If the firmware does not help, then most likely there is a problem with the memory chip and it will need to be replaced, and failures in the charging circuit, with the battery or other elements on the board are also likely.
Good afternoon. Most likely the firmware has crashed. When changing software on Honors, there are some nuances. or alternatively the memory chip is faulty
Good day! In your case, most likely there is a problem with the main memory. This happened many times with the Honor line. It can be solved by replacing the memory followed by flashing the firmware. The cost starts from 3500
Replace either the battery or set your phone in a switched off state for 5 minutes after setting it for 10 minutes, then keep the phone without charging for 5 minutes and with charging for 30 minutes and turn it on.
Most likely faulty: charging controller, motherboard, charging circuits, processor, memory chip, software failure. Diagnostics at a service center is required.
Replacement of a pair of microcircuits on the 5V line, 2000 rubles
If the battery is excluded, then you should recheck the charging controller. This picture may occur if the phone’s flash memory is faulty.
You need to open the device and look for faulty elements, most likely moisture
Diagnostics is required, the charging controller or charging circuit is probably faulty.
The problem may be in the system connector, controller and charging circuits, memory chip. It is likely that the new battery is also discharged.
The root cause may well be in the system! Therefore, I don’t recommend immediately taking it to repair; very often, it’s permissible to fix everything yourself. You can read in detail how and with what here
Keep it up! What is your question?
This is not surprising. Because he is Huawei.
.
But seriously, try to reflash it. This happens to many phones.
Probably faulty: charging controller, system board, charging circuits, processor, memory chip, software failure. Diagnostics at a service center is required.
You need to open the device and look for faulty elements, there may be moisture
It is necessary to carry out diagnostics; the charging controller or the charging circuit may be faulty.
The problem may be in the system connector, controller and charging circuits, memory chip. It may be that the new battery is also discharged.
Probably a deep discharge of the battery. Try leaving it on charge for 8 hours. If it doesn’t help, take it to a service center for diagnostics.
Good morning) looks like a burnt out charge controller.
Diagnostics is necessary; the problem may be in the software, system connector, battery, or board.
Good afternoon! First, check the condition of the battery and charger connector; if they are in order, then check the charging controller and flash memory.
How did you behave 24 hours before the shutdown? Did it get hot and produce errors? Did you misrepresent the charge percentage? What’s wrong with it and how to fix it largely depends on this.
First of all, you need to measure the voltage on the battery, and if it is below 3.7 volts, then charge it directly. After this, disconnect the battery and try to start the phone. You also need to measure the current consumption of your phone. If a current leak is detected, the charging controller is most likely faulty.
The memory is faulty and cannot be repaired.
Good evening, I had a similar problem and was solved by juggling the battery cable.
Good afternoon, my name is Dmitry, there are many reasons for this breakdown, faulty battery, broken firmware, board faults. If the charging controller is faulty, first try to reflash it; if it doesn’t help, you will need diagnostics in a service center.
Most likely the battery, charging connector, charging controller, charging circuits, system board, activation button, processor, memory chip, software failure are faulty. Try to do a hard reset in recowery. If it doesn’t help, then diagnostics are needed at a service center.
Good afternoon! You need to double-check the activation button cable, most likely the problem lies there. If there are no defects, then there may be a problem with the light sensor. The problem may also be in the software, resetting the settings should help in such a situation
Good afternoon.
To make sure that your version is correct, you need to disassemble the phone and get to the buttons, accordingly clean the button cable and recheck their functionality. Also clean the phone case. If after these procedures the problem does not go away, then most likely the problem is in the main board. Diagnostics at the SC is required. Good luck!)
When activated, it is cut off. Huawei Y-360-U61 – video answer.
Huawei aspend p1 lte turns itself off – video response.
Add answer to question
How many answers to the question?
There are 98 answers to the question “The Honor phone turns on and off.”
Who asked this question?
Question asked by Kuzneczov_Pavel in the Phones category.
When was this question asked: “The Honor phone turns on and off”?
Question asked 3 years ago.