Command not allowed fastboot huawei

We are installing software to your huawei phones that have been bricked or stucked at the logo.

WHATSAPP : 00213770833038

We are solving your certain problems cited below and make a new clean install.
100% percent working.
100% money back guarantee.

View Full Version : Huawei Honor 8 Bootloader Unlock and Brick Repair

Good evening.

I think first you need to revive the phone by flashing the firmware corresponding to its bootloader, which should be written without unlocking the bootloader.

Good evening.

I think first you need to revive the phone by flashing the firmware corresponding to its bootloader, which should be written without unlocking the bootloader.

Bouygues Telecom is a French operator.

Thanks Pavel, so the goal is to find a native factory firmware, if I can do it, I’ll unsubscribe.

Here I also used the service, the answer came:

Model: PRAGUE-TL00R

IMEI: 86*********96

S/N: 7Y**********02

Company: ГђЕѕГђЕѕГђЕѕ ГђвЂќГђВќГђВЎ ГђВ ГђВёГ‘вЂљГђВµГђВ№ГђВ»

Warranty Type: 1000

Warranty Expire: 2018-10-14

Delivery Date: 2017-08-10

Sold-to Country: Russian Federation

Ship-to Country: RU MOSCOW

Additionally, I also wrote in support, they do not have firmware, but I managed to find out with what firmware they were produced from the factory, I am attaching a photo. I already flashed this version, but without success ((.

Native firmware should get up without a fastboot from the card. It is clear that she will not get up through the fastboot. Well, the prehistory is not clear why they started sewing it at all. Often, phones with hardware problems begin to be sutured, and as a result, a full-fledged brick is ready.

It’s strange that he doesn’t want to be flashed with native firmware. Must.

And by what criteria did support determine the version of the factory firmware?

Maybe they were wrong?

History is silent about this)

I apologize in advance for writing in someone else’s topic There is a Huawei P8 lite 2017 (PRA-LA1) device, it hangs on the splash screen, it only enters fastboot mode. In fastboot mode, FRP is enabled. Will the HCU program work in fastboot mode if I order the FRP unlock service? Service firmware via SD card does not accept (it just remains hanging on the splash screen)

As I understand it, in both cases there will be the following recovery algorithm:

1. Remove FRP (since it does not allow unlocking the bootloader)

2. We calculate the bootloader unlock code through the site (in my case, everything has already been calculated) and enter it through fastboot

3. Restore with the Huawei_Multi-Tool utility on the scratching tab.

Correct me if I’m wrong

On this issue, you better contact the HCU client program support CHAT (http://messenger.providesupport.com/messenger/digiteka.html)

Ordered a service, reset FRP, stayed closed Before detection connect cable to usb and enable Manufacture mode !

Qualcomm and HiSilicon: *#*#2846579#*#*

MTK: *#*#14789632#*#*

Windows: ##2846579#

ProjectMenu

1. Background setting

2. USB ports setting

Select Manufacture mode

Account: masalius

Check success!

Credits left: 12

2017-10-26 22:42:59.702 Start read phone info from fastboot!

2017-10-26 22:43:00.632 Read phone info done!

Model: PRA-LA1

IMEI: 86**********500

Firmware ver.: PRA-LA1C10B100

SN: PSEDU17115001521

Account: masalius

Check success!

Credits left: 0

2017-10-26 22:45:52.872 Start read phone info from fastboot!

2017-10-26 22:45:53.796 Read phone info done!

Model: PRA-LA1

IMEI: 863159030368500

Firmware ver.: PRA-LA1C10B100

SN: PSEDU17115001521

What exactly was left closed? Bootloader?

In fastboot mode, it says in green below: PHONE Locked FRP Lock, in the program log at the end, a repeated request for info shows that the FRP remains:

Account: masalius

Check success!

Credits left: 0

2017-10-26 22:45:52.872 Start read phone info from fastboot!

2017-10-26 22:45:53.796 Read phone info done!

Model: PRA-LA1

IMEI: 86**********500

Firmware ver.: PRA-LA1C10B100

SN: PSEDU17115001521

For this issue, you better contact the HCU client support CHAT (http://messenger.providesupport.com/messenger/digiteka.html)

Does HCU support respond to messages in Russian?

Yes, he also answers in Russian, no problem.

In fastboot mode, it says in green below: PHONE Locked FRP Lock, in the program log at the end, a repeated request for info shows that FRP remains:

Account: masalius

Check success!

Credits left: 0

2017-10-26 22:45:52.872 Start read phone info from fastboot!

2017-10-26 22:45:53.796 Read phone info done!

Model: PRA-LA1

IMEI: 86**********500

Firmware ver.: PRA-LA1C10B100

SN: PSEDU17115001521

We have similar problems, did you manage to unlock the bootloader in the end?

As you can see, no, FRP lock does not unlock the bootloader

As you can see, no, FRP lock does not allow unlocking the bootloader

and they tried to flash it with «Service firmware» — they wrote down the UPDATE file. APP to a flash drive or update.zip? And tried to flash by pressing 3 buttons?

As shown here https://4pda.ru/forum/index.php?showtopic=772246&st=800#entry55689846 on a visual instruction on phone modes.

As you can see, no, FRP lock does not allow unlocking the bootloader

And after you command fastboot oem unlock «code» also writes Failed

command not allowed?

I tried the service with sd — nothing even happens, it remains to hang on the splash screen, in fastboot the same reaction to commands when entering the code

Call accepted by operator Valdemaras. Currently in room: Valdemaras, Alexei.

Valdemaras:

read here https://forum.dc-unlocker.com/forum/modems-and-phones/huawei/163403-frp-unlock-not-working-money-wasted-read-here

Valdemaras:

credits added back

Alexey:

It turns out that I now need to flash it with DC-Phoenix, the program cannot complete the unlock procedure because the phone is «branded»?

Valdemaras:

yes

Valdemaras:

there is no gurantee that dc-phoenix will help either if phone is bricked

Alexey:

Supported

Valdemaras:

yes it is supported for flashing

Alexey:

There is no P8 lite PRA-LA1 model in the supported list, there are others of this model — will the program work?

Valdemaras:

yes it will allow you to flash your phone

Alexey:

OK! I activate Phoenix, I fully charge it, I will flash it. Another question — after the firmware FRP will not remain?

Valdemaras:

if you talk about FRP lock in fastboot it will remain forever until you change it in phone settings, developer options by enabling oem unlock

Valdemaras:

https://www.dc-unlocker.com/huawei-phone-disable-frp

Valdemaras:

it was written in first link i gave man

Alexey:

Thanks for the complete answers! We will restore

Valdemaras:

most welcome

Question to Pavel — through which service to activate DC-Phoenix?

I tried the service with sd — nothing even happens, it remains to hang on the splash screen, in fastboot the same reaction to commands when entering the code

And what kind of service — file UPDATE. APP or update.zip archive? And in what way are you trying to flash — with three buttons?

And which service one exactly — the UPDATE file. APP or update.zip archive? And in what way are you trying to flash — with three buttons?

UPDATE file. AAP 3 button method

Device found: 7YYDU17713001602

IMEI: 864645031946996

Build number: :PRA-TL10C10B170

Product model: PRA-TL10

Cannot update device in upgrade mode

As far as I know, there are 2 partitions in the phone, maybe 1 partition is deleted and because of this the phone does not start, then the question is how to restore the second partition where the e-recovery is located and this forced firmware mode?

according to your model (Model: PRAGUE-TL00R, this is from your phone info) there is a service firmware on the DC-unlocker support, you will get access to the file partition through DC-Phoenix, you will find it in the file partition, though it is not for our region: PRAGUE-AL00a, but in a neighboring forum (MCRF) a person used it to raise your model, but he had a backup flash read by the programmer, the device after flashing it started up with a zero IMEI

according to your model (Model: PRAGUE-TL00R, this is from your phone info) there is a service firmware on the DC-unlocker support, you will get access to the file partition through DC-Phoenix, you will find it in the file partition, though it is not for our region: PRAGUE-AL00a, but in a neighboring forum (MCRF) a person used it to raise your model, but he had a flash backup read by the programmer, the device after flashing it started up with a zero IMEI

Looking for a device in fastboot mode

Device found: 7YYDU17713001602

Erasing CACHE partition

Partition CACHE erased

Is this the Prague-AL00A entry log?

Looking for a device in fastboot mode

Device found: 0123456789ABCDEF

IMEI: 864645031946996

Build number: :PRA-TL10C10B170

Product model: PRA-TL10

Erasing nvme partition

Partition nvme erased

Erasing cust partition

Partition custom erased

Erasing misc partition

Partition misc erased

Erasing cache partition

Partition cache erased

Erasing cust partition

Partition custom erased

10/30/2017 02:48:28 PM Writing device finished OK

Checking fastboot device

Device found: 0123456789ABCDEF

10/30/2017 02:48:29 PM Starting extracting partitions from file UPDATE. APP

Current version: PRA-LX2C999B000

Cannot create extract directory: D:\HW\Huawei 170\DC_Phoenix\tmp\20171030_144829_UPDATE\

Extract files to directory: D:\HW\Huawei 170\DC_Phoenix\

Extracting partition: XLOADER OK

Extracting partition: FW_LPM3 OK

Extracting partition: FASTBOOT OK

Extracting partition: MODEMNVM_UPDATE OK

Extracting partition: TEEOS OK

Extracting partition: TRUSTFIRMWARE OK

Extracting partition: SENSORHUB OK

Extracting partition: FW_HIFI OK

Extracting partition: BOOT OK

Extracting partition: RECOVERY OK

Extracting partition: RECOVERY2 OK

Extracting partition: DTS OK

Extracting partition: MODEM_FW OK

Extracting partition: SYSTEM OK

10/30/2017 02:49:14 PM Extracting partitions finished OK

Device found: 0123456789ABCDEF

IMEI: 864645031946996

Build number: :PRA-TL10C10B170

Product model: PRA-TL10

Device found: 0123456789ABCDEF

I also noticed that they are missing, and with firmware from sd it says: Software install failed!

I’ll try to flash this soon File: Service Full Repair PRA-TL00R C10B170 Russian Federation Android 7.0

download from here http://4pda.ru/forum/index.php?showtopic=820467&st=860#entry66276946

By the way, everything is ok with IMEI, only the serial was damaged, but the phone rings normally, the serial is standard 12345ABCDE

How It Works

We will connect to you via Teamviewer and install new working rom to your bricked Huawei Phone!
Required:
Teamviewer, 8 GB sdcard, skype, PC , Paypal or Payoneer Account.
Phone must be open, I mean at least you should any logo, fastboot mode see or recovery.
Battery Charge must be over 60%.

Step by Step Fix Process

1-You will ask for your model number.
2-We will prepare required files.
3-You will pay the service fee via Paypal or Payoneer.
4-We will send you the files.
5-And you will download required files from our google drive accout. (it may last 20-30 minutes according to your internet speed)
6-We will connect to your Pc through Teamviewer or Ammy application and also with Video call on Skype.
7-We will load the files to your bricked phone.