HUAWEI AR600 Series Routers User Guide

Список паролей по умолчанию для роутеров Huawei позволяет менять настройки раздаваемой сети Wi-Fi.

Quick Start GuideAR600, AR1600, AR6000, and AR6000-SSeries Routers

Issue: 10 (2021-07-09)Part Number: 31509419HUAWEI TECHNOLOGIES CO., LTD

About This Guide

Scenario 1: Desk MountingBefore You Start

Step 1 Attach four rubber pads to the bottom. Step 2 Place the router on a desk. Step 3 (Optional) Install a security lock. Step 4 Connect the ground cable to the ground point.

Scenario 2: Wall Mounting (through the Installation Holes)

Installation ProcedureStep 1 Use the marker to mark installation hole positionsStep 2 Fix M4 mounting screws against the wall and leave a 2 mm distance away from the wall. Step 3 Hang the router on the mounting screws. Step 4 Connect the ground cable to the ground point.

Scenario 3: Wall Mounting (through the Mounting Brackets)Before You Start

Installation ProcedureStep 1 Use a Phillips screwdriver to fix the mounting brackets to both sides of the router using M4 screws, with a torque of 1.4 N·m. Step 2 Use a measuring tape to determine the four mounting bracket installation positions. Keep the upper and lower installation positions respectively on a  horizontal line and mark the positions with a marker. Step 3 Drill holes and install mounting expansion bolts in the wall.a. Use an 8-mm drill bit to drill holes in the marked positions.b. Insert M6 expansion bolts into the holes and screw the M6 nuts to fasten the expansion bolts.c. Remove the nut, flat washer, and spring washer. Step 4 Place the router on the M6 expansion bolts, fasten the spring washers, flat washers, and nuts in order, and secure the router on the wall using a torque wrench, with a torque of 5 N·m.

Scenario 4: Cabinet/Rack Mounting

AR6280 sub-series/AR6300 sub-seriesThe chassis is heavy, so it is recommended that you install guide rails (separately purchased) in the cabinet to support the chassis.

Installation ProcedureStep 1 Attach mounting brackets to the router with M4 screws. Determine the mounting method according to the brackets delivered with your router.

Step 2 Install four floating nuts on front mounting rails, two on each side. Install the floating nuts in two mounting holes with one hole between them. Step 3 Hold the bottom of the router and push the router into the cabinet. Step 4 Use M6 screws to secure the router onto the cabinet/rack. Step 5 Connect the ground cable to the ground point.

Scenario 1: Not Removing Guide Rails

Installation ProcedureStep 1 Use a Phillips screwdriver to loosen the captive screw on the filler panel counterclockwise. Step 2 Pull the filler panel out by the captive screw. Keep the filler panel for future use. Step 3 Turn the eject lever of the card 45 degrees outward. Push the card into the chassis with your thumbs. Step 4 Rotate the ejector lever inward to lock the card after the card is completely in the chassis. Step 5 Use the Phillips screwdriver to fasten the captive screws clockwise.

Scenario 2: Removing a Guide RailInstallation Procedure

Step 1 Use a Phillips screwdriver to loosen the captive screws on the filler panels on the two SIC slots counterclockwise. Step 2 Pull the filler panel out by the captive screw. Keep the filler panel for future use. Step 3 Use the Phillips screwdriver to loosen the screw on the guide rail. Step 4 Remove the guide rail in the middle of the chassis. Step 5 Turn the eject lever of the card 45 degrees outward. Push the card into the chassis with your thumbs. Step 6 Rotate the ejector lever inward to lock the card after the card is completely in the chassis. Step 7 Use the Phillips screwdriver to fasten the captive screws clockwise.

Logging In to the Router for the First Time

8.1 Using the console interface login settingsBefore You Start

• Transmission rate: 9600
• Data bit

  : 8

• Stop bit (S): 1

8.2 Using the web login settingsBefore You Start

Obtaining Product Documentation and Technical Support

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective holders.

Documents / Resources

Quick Start Guide for AR600, AR1600, AR6000 and AR6000-S Series Routers

Issue: 10 (2021) Part Number: 31509419KO. HUAWEI T ECHNOLOGY CO., LTD

About this guide

Scenario 1: Desk Setting Before You Begin

Step 1 Attach four rubber pads to the bottom. Step 2 Place the router on a table. Step 3 (Optional) Install a security lock. Step 4 Connect the ground cable to a grounding point.

Scenario 2: wall mounting (through mounting holes)

Installation processStep 1 Mark the positions of the mounting holes with a marker. Step 2 Attach the M4 mounting screws to the wall and leave a distance of 2mm from the wall. Step 3 Hang the router on the mounting screws. Step 4 Connect the ground cable to a grounding point.

Scenario 3: Wall mounting (using mounting brackets) Before you start

Installation ProcessStep 1 Use a Phillips screwdriver to secure the mounting brackets on both sides of the router with M4 screws with a tightening torque of 1.4 N·m. Step 2 Use a measuring tape to determine the four mounting bracket mounting positions. Keep the top and bottom mounting position respectively on a horizontal line and mark the position with a marker. Step 3 Drill holes and install mounting plugs in the wall.a. Use an 8 mm drill bit to drill holes in the marked areas. b. Insert the M6 ​​spacer bolts into the holes and tighten the M6 ​​nuts to secure the spacer bolts.c. Remove the nut, flat washer and spring washer. Step 4 Install the router on M6 spacer bolts, fasten the spring washers, flat washers and nuts in order, and fix the router to the wall using a torque wrench with a tightening torque of 5 N m.

Scenario 4: Cabinet / rack mounting

AR6280 Sub-Series / AR6300 Sub-Series The chassis is heavy, so it is recommended that rails (purchased separately) be installed in the cabinet to support the chassis.

Installation processStep 1 Attach the mounting brackets to the router with M4 screws. Determine the mounting method according to the brackets that came with your router.

Step 2 Install four floating nuts on the front mounting rails, two on each side. Install the floating nuts in the two mounting holes, leaving one hole between them. Step 3 Grasp the bottom of the router and slide the router into the cabinet. Step 4 Use M6 screws to secure the router to the cabinet/rack. Step 5 Connect the ground cable to a grounding point.

Scenario 1: Do not remove guide rails

Installation processStep 1 Use a Phillips screwdriver to loosen the captive screw on the filler panel counterclockwise. Step 2 Pull out the fill plate using the captive screw. Save the pad for future use. Step 3 Rotate the card eject lever 45 degrees outward. Insert the card into the case with your thumbs. Step 4 Turn the ejector lever inward to lock the card after the card is fully inserted into the case. Step 5 Use a Phillips screwdriver to tighten the captive screws clockwise.

Scenario 2: Removing the railInstallation process

Step 1 Using a Phillips screwdriver, loosen the captive screws on the plugs on the two SIC slots counterclockwise. Step 2 Pull out the captive screw. Save the blank for future use. Step 3 Use a Phillips screwdriver to loosen the screw on the rail. Step 4 Remove the rail in the middle of the chassis. Step 5 Rotate the card eject lever 45 degrees outward. Insert the card into the case with your thumbs. Step 6 Turn the ejector lever inward to lock the card after the card is fully inserted into the case. Step 7 Use a Phillips screwdriver to tighten the captive screws clockwise.

First login to the router

8.1 Using Console Interface Login SettingsBefore you start

Step 1 Turn on the power switch on the external power supply and log into the router after the SYS indicator flashes every 2 seconds (indicating that the router is working properly). Step 2 Use a console cable to connect a PC to the router’s console interface. Step 3 Run the terminal simulator, create a connection, configure the connected port, and set the communication parameters as shown below.

• gearbox rating: 9600
• Data bit
  : 8
• Stop bit (S): 1

Step 4 Press Enter until the following information is displayed. (The following information is for reference only)

After successfully logging in, you can configure the router in the CLI. For more information, see the “Product configuration based on the command line interface” section.

8.2 Using web login setupBefore you start

On the web page, you can configure the router. For more information, see Web Based Product Configuration.

Get product documentation and technical support

For more information, see Product Open Source Notice.

Hereby Huawei Technologies Co., Ltd. declares that the type of radio equipment is in conformity with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: www.huawei.com/en/product-certi cation.

Supplier Declaration of Conformity (SDoC)

Unique identifier: trade name: HUAWEI; Product Name: Router; Model Number: AR600, AR1600, AR6000, and AR6000-S Series Routers Responsible Party – US Contact InformationHuawei Technologies USA Inc.5700 Tennyson Parkway, Suite 500Plano, TX 75024Main: 214-919-6000 / TAC Hotline: 877 -448-2934 FCC Declaration of Conformity (For Part 15 products) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd. All other trademarks and trade names mentioned in this document are the property of their respective owners.

Documents / Resources

We have tried to cover as many of the Huawei router models in use in South Africa in the above table. But what do you do if the router that you have does not feature here? Remember that Huawei manufactures a wide range of routers and modems.

Login information is usually on the router label

If you check underneath your Huawei router, there will be a label on there on which will be printed all the information that you need to sign into the device’s dashboard. So, that should be your first port of call if the information here does not work.

Reset your router

There are times when you will have to reset your router in order to log in using the defaults given here. That usually happens if your Huawei router password has already been changed and if you have forgotten the new login details.

That happens a lot. Router passwords are seldom used, unlike WiFi password. So, you can easily forget your router password. Should that happen to you, you will need to reset the device to be able to sign in. Once you have done so, you will have to reenter the settings for your network.

As an example, you may need to reenter the Telkom APN settings for your Huawei router. So, that’s something to keep in mind. You shouldn’t reset your router without knowing what you are doing. Otherwise you will lose all your settings. Not too difficult a situation, but it can be a hassle.

Which networks use Huawei routers in South Africa

As an example, a number of Telkom customers have the Huawei E5576 . Vodacom customers also use Huawei routers, as well as MTN customers. So, this is a very popular brand in the country. Hopefully, the information that we provided will enable you to quickly and easily log in.

How to reset to factory settings?

To reset the settings to the factory settings (this option is suitable if you can’t log in using standard passwords), you need to find the reset button and hold it down for 5-10 seconds (see photo).

Default Huawei Router Login Details

Wi-Fi password