Link hidden from guests
I tried. Not suitable
I’m not very good at optical communications. In general, everyone assures me that I myself will not set it up without knowing some kind of key that only the provider knows. That is, I have PPPOE data, but I don’t have that network key (or what its name is, I don’t even really understand what I’m talking about)
You must have an agreement with the provider in your hands, which contains the login details. In any case, by contacting the technical support line, they are obliged to assist in the settings. I don’t know who your provider is, the feds of the norms help.
I picked up help on commands
Is there a «reset» button on the router or something like that?
When my router freezes and I’m too lazy to fix it (mainly a problem with MAC addresses), I keep this button pressed for 20 seconds and voila: 18 characters of the password are reset, I open the browser in the search field I write:
The initial settings tab opens. I put a password, write the SSID and select the option * dynamic ip *, after all this wifi works, you can use it.
Have you tried going through the list of possible default passwords?
If it doesn’t work, you can try to extract the password from the device via telnet from the root account
As a result, the last command gives information about what is happening in the web interface
Source
Last edited: 08/23/2020
Yes, unfortunately, none of the passwords presented anywhere is suitable.
Yes, I would have dropped it 20 times already. What is this parameter?
What is this password? As far as I understand, there will be trouble without this password. Once again I want to emphasize the fact that I have no idea how the Internet connection is configured via optics. I pulled the optics several times. Then they boiled it for me, I stuck an optical patch cord from both ends into a switch in sfp and the network rose. This is all my knowledge about optics. If I had a cable connection, I would have done it in 3 minutes. And then they scared me, they say: if you drop it, you won’t set it up. So I’m looking for advice (answer, hello)
Yes, I would have dropped it 20 times already. What is this parameter? View Attachment 43352
What is this password? As far as I understand, there will be trouble without this password. Once again I want to emphasize the fact that I have no idea how the Internet connection is configured via optics. I pulled the optics several times. Then they boiled it for me, I stuck an optical patch cord from both ends into a switch in sfp and the network rose. This is all my knowledge about optics. If I had a cable connection, I would have done it in 3 minutes. And then they scared me, they say: if you drop it, you won’t set it up. So I’m looking for advice (answer, hello)
I think you have a password with asci characters
try decoding ASCII to Decimal, google ASCII to Decimal
Yes, this is a picture from the Internet. Just attached. I can’t get here. I’m worried that after the reset this parameter will also be reset. And as far as I understand, without it, not only to the Internet, you can’t connect to their network. If I’m wrong, please correct me
Yes, when connecting via telnet, it allows you to execute commands only in the shell, you need to get out of it.
Here is the instruction for HG8245Q, but I think it’s worth a try, I’ve outlined the steps below (
After entering this command, the router will ask for a password, the password is somehow generated.
On the Internet, I found a script into which you put the code string that the router gave you, and the script gives you a password
Next, enter this password, get root access and enter the command
And in theory, that’s it, now you are not working in the shell and you can execute the commands written above
After entering this command, the router will ask for a password, the password is somehow generated.
View Attachment 43362
On the Internet, I found a script into which you put the code string that the router gave you, and the script gives you a password
View attachment 43361
Then you enter this password, get root access and enter the command
Thank you very much for your reply. I came across this article. I went to open with a bang. But only, as far as I understand, there is a certain list of commands and only they are supported. The list of these commands is opened by sending the character «?» And if in this shell I can at least enter something, then there are two commands in the shell: exit and this script that shows the version. Nothing more. I’ll try to attach a video now. The computer is now trying to brute, so from the phone
I can’t upload the video for some reason Well, here it is in general.
Here I have a dead end. The file is, but how to look xs. I’ve been scratching my head all day. Standard commands are not accepted. Only those that this neutered busybox offers.
It seems that there is some kind of “display file” command, but I don’t understand how to use it.
Here I have a dead end. The file is, but how to look xs. I’ve been scratching my head all day. Standard commands are not accepted. Only those that this neutered busybox offers.
It seems that there is some kind of “display file” command, but I don’t understand how to use it.
Moving in the right direction))
When you get into busybox, you should be using other commands than what the initial shell shows.
With the video, it became easier to understand what is happening there.
I tried to execute these commands in order when I got into busybox
Looks like your busybox is heavily neutered
run the command and attach a screenshot of the output, it should show what can be done with it
UPD2
Here is another way to backup a configuration and then extract the password from it
Thank you very much. So I report. With a backup did not grow together. Refuses to eat the backup cfg command, as well as does not eat cd and the like. From navigation only viewing of contents of directories wap list (type ls) Passwords tried. None fit. Maybe there is some kind of exploit that zhahnet there was a normal one? Maybe someone knows? Tell me please
Are you sure about that? Is it that the password will be reset, and the devices at the edges of the optics will make friends with each other after such a procedure?
99.9% yes.
As I understand it, your provider pulls a PON network, like «optics». Last mile equipment, ONT terminals (routers), not independent devices, are configured centrally through the AMS network management center. Resetting the router config and connecting it back to the optics, 99. 99% that he will pick up the AMS config, grabbing it with pleasure and will not give access to the web face again
99.9% yes.
As I understand it, your provider pulls a PON network, like «optics». Last mile equipment, ONT terminals (routers), not independent devices, are configured centrally through the AMS network management center. Resetting the router config and connecting it back to the optics, 99. 99% that he will pick up the AMS config, grabbing it with pleasure and not giving access to the web face again
Thank you so much! I’ll try it tonight and report back.
Don’t you want to use another router? I do not use RT routers. Set it up in bridge mode and connect yours. Pick up PPPOE on it and ride.
As an option.
8245 switch to bridge mode and then connect the wire to wan connector 615
Connection Name******************VLAN/Priority**********IP Acquisition Mode2_VOIP_R_VID_12**************** **12/7********************DHCP3_TR069_R_VID_9********************9/7**** ****************DHCP1_INTERNET_R_VID_10***************10/0******************** **PPPoE
I understand that the third setting should be transferred from route to bridge?
Post has been editedlinkpj — 01.02.15, 16:50
Didn’t find a new firmware?
No, I haven’t found it yet (I’ve already registered on their support site, not good people hid it) Only 122. But I’m wondering if you reset at 122 in Rostelecom, can you log in under the factory admin? In principle, if you figure out the firmware is no longer Rostelecom, but the factory one is not their clumsy one. When I did a reset in 106, it didn’t reset, and I disconnected the optics from the router, everything was useless, the same settings remained
I thought officially that they would open LAN ports, I called their support service. So they told me that the firmware is St. Petersburg and it is not possible to open ports there, our specialists tried not to open. Well, I think to myself that you’re lying, I realized that it’s impossible, well then, thanks for your attention, goodbye. It’s good when there is an admin password, and when you know it. So I opened myself 1-3 and left 4 on the prefix.
So I understand that through telnet?
Added on 02/01/2015, 17:57:
It gives me an error. Maybe something with a computer
I don’t think so. Did you ask him for the firmware number?
Post has been editedTelenor — 01.02.15, 18:33
I didn’t ask, I asked about what might not work with the new one. I answered that these are standard Linux commands, which is what it is. Try it, I sin on my computer
Try it, I sin on my computer
linkpj, Quite right, and you will already be raising PPPoE on D-link
Everything is fine at 106, but something is wrong with 122(
So it doesn’t work for me at 122
The password doesn’t work for some reason. It can be seen that the Chinese covered in the new firmware. And on 106 I did a rollback, everything is fine. And you ask him maybe there is some other team.
Guys tell me what is the latest firmware on HG8245H?
Dear, recently connected to Rostelecom and installed this optical terminal, there were questions about its setup, operation: 1. Is the firmware V1R006C01S122 worth updating? And what is the last one? How to register permanent IP addresses for PC, PS4 and others3. ChromeCast can’t connect to WiFi, what’s the problem?4. T R-069 do you recommend to disable or let the provider manage the terminal?5. How to get access via telnet? It seems that I entered the name password, they asked me to change the password — it doesn’t work
Post has been editedTaktik — 07.02.15, 21:52
This firmware is the penultimate one. The last one is nowhere
I will say one thing, that flashing to a newer one will positively affect the speed via wifi
So can I flash 122? Or is this firmware only available under Rostelecom? I have MGTS.
Still, how to put 8245 into bridge mode? In WAN Config — binging option I can not change anything — the options are not active.
Hardware Specifications
HG8010H: Horizontal PON port (left, middle); vertical PON port (right)
Bottom of the HG8010Hv3/4/5
Bottom of the HG8010Hv6
Hardware revisions
0x000000000000-0x000000100000 : “bootcode” (1MiB) 0x000000100000-0x000008000000 : “ubilayer_v5” (127MiB)
Enabling telnet
We need access to a specific shell and in order to get it we have to enable telnet. On the unit, the telnet server accepts connections but doesn’t read any input, nor does it send anything.
To enable telnet we’ll use one of the web interface’s features: the configuration backup and restore page. The configuration can be downloaded as an XML, which contains a lot more options than the web interface and a couple of them can be modified to enable telnet access: under the X_HW_CLITelnetAccess node, set the Access attribute to 1 and in AclServices, TELNETLanEnable should also be set to 1. I had to set both but your mileage may vary.
It is possible that this won’t work/has been fixed in more recent versions.
Now that this is done, the modified configuration file can be uploaded via the web interface, the ONT will restart and telnet should be accessible on port 23.
Get information of the OLT vendor
